How to start a dishwasher for the first time

Finally, the long-awaited acquisition of the first dishwasher took place. Indeed, until recently, such a device from Bosch or Siemens significantly emphasized the status of its owners.

Today, this technique has become much more affordable. It’s crucial to find out how to operate the dishwasher and how to conduct its first launch.

Still, this technique is still new to most of us. But dishwashers, even such budget ones as Candy or Flavia, belong to the category of sophisticated household appliances that require initial testing.

Therefore, do not rush, it is better to carefully read the technical instructions for the unit. If not everything is clear in the accompanying description, then this article will give the necessary tips on how to conduct a test run, especially if this is the first dishwasher in your kitchen.

Getting Started

After removing the packaging from the machine, subject it to a thorough inspection. If there are complaints about the condition of the unit, it is better to immediately call a specialist from the service. If everything is in order with the dishwasher, you need to check the equipment, remove the protective clips and proceed with installation.

After installing the device, most consumers have an irresistible desire to turn on the dishwasher and evaluate the results of its work. Many manufacturers, such as Asko, Whirlpool, Electrolux strongly recommend a mandatory test run.

A test run is at the same time an opportunity to verify the correct installation of the device:

• The structure should be located on a solid, level surface. Even a slight deviation from the horizontal level can lead to malfunctions and additional noise and vibration.
• It is not recommended to install a dishwasher under the kitchen hob. It will generate excess heat, and its magnetic radiation can cause incorrect operation.
• It is necessary to make sure that the electrical outlet is working, the connecting wire of the machine should not get warm when it is turned on. It is advisable not to use extension cords when connected to AC power.
• Especially carefully check that the cold water supply valve is working; it must completely block the water. This is necessary for quick shutdown in case of leakage.
• It is necessary to check the water supply hose itself, if possible, it is necessary to install an additional filter.
• When connecting the device to the sewage system, it is important to ensure that the drain hose is not bent or pinched. It must be well fixed in the corresponding hole in the machine.
• When closing the dishwasher door, a distinctive click sound should be heard. The impeller should rotate evenly and smoothly.

Why is idle start up necessary?

As noted in the operating instructions for dishwasher bosch, test start-up of the device is an inevitable operation before the beginning of continuous operation. Only through this procedure can you be sure in the correct mode of operation of the dishwasher, and at the same time clean it of transport dust and dirt.

Part of the parts of the dishwasher comes from the factory in technological lubricant. A small amount of debris may be present inside the device; during further operation, it may clog filters.

Many consumers want it right the first time load cookware and check the effectiveness of the new purchase. It is not right.

The first wash cycle is necessary to get rid of technical grease and factory debris that may be inside the unit.The ingress of these foreign substances into the kitchen utensils can only disappoint the owner of the machine. Therefore, it is enough to install all the baskets in the tank.

Important! During the test inclusion, you need to clarify:

• water collection rate;
• degree of water heating;
• whether water is drained at the end of the cycle;
• type of drying in the dishwasher and correct temperature settings.

All of these functions should work properly.

Failure on first start

There are a considerable number of reasons why the dishwasher does not show signs of life during a test inclusion.

Before the first start-up, it is necessary to carefully study the operating instructions. It will give detailed information about the functional purpose of the buttons, it contains a description of all the main components of the mechanism and a decoding of possible errors.

Such minor breakdowns as a filter blockage or a pinch of the hose can be eliminated independently, but what if along the way work dishwasher makes strange noises or in a critical form smoke and the smell of overheated plastic are noticeable.

1. If a message appears on the board error code or several bulbs start to flash immediately - look at the instructions which node is diagnosed as faulty.
2. If smoke begins to appear (no matter which one is dark or white), and the smell of burnt plastic is felt, you must immediately turn off the device from the network. These signs characterize a serious defect in the machine, improper assembly of the device is possible, therefore, it is necessary to call the master under warranty.
3. The machine “freezes” in the middle of the program, which means a system failure of the electronics. The following may help: you must disconnect the device from the network for 15 minutes and then turn it on again. If failures are observed several more times, then professional assistance is needed.

It is almost impossible to fix a system defect on your own, you need to call a qualified specialist. But if the unit is new and gave a serious malfunction at the first start, it is better to replace the machine, or repair it for free under warranty.

Important! Before purchasing the device, carefully read the possibilities of providing warranty repairs.

Serious trading companies such as Bosch, Gaggenau, Miele provide quality services in most major cities.

First run order

Carefully inspect the internal surfaces of the device, remove unnecessary stickers from them, remove packing pads and pieces of wire, foam balls.

Important! Before the test start-up of the device, it is necessary to open the water, otherwise the washing program will not start.

Never allow the machine to come into contact with wet hands. Also carry out a test run only indoors, in no case outdoors.

Attention! Test washing of the unit does not yet indicate that it must be carried out without detergent ingredients. Detergents as well as salt are required during the first run.

At the beginning of the test, it is necessary to determine what is desirable to use for washing: liquid gel, powder or tablets. Using the buttons on the control panel of the device, it is necessary to set the position which means are used.

If before there was no experience in operating such a device, and there are no skills in using household chemicals, then it makes sense to purchase a starter kit. It consists of the necessary ingredients for the full operation of the device. Now you can start the test run:

1. Initially, the lower basket needs to be pulled forward. At the bottom of the unit you can see the salt compartment. Remove the cover and fill the compartment. the dishwasher with ion salt in the right amount, It is also used to reduce the hardness of water (approximately 400 grams). To do this, you can use a special funnel, which comes with the device. So that the salt does not stick together, it is advisable to pour about a liter of water into the receiver. Excess of this water will go into the tank, it is not dangerous.
2. Place the required amount of detergent in the desired compartment and make the necessary settings on the front panel. Some models recognize chemistry on their own.
3. Pre using test strips hardness is determined tap water. Then you must definitely enter the salt supply mode in the memory of the dishwasher, which is determined precisely by the hardness of the water. If for some reason the equipment is left without electric energy, then in almost all models these settings will need to be re-entered. Also set the control panel to medium temperature.

We set any washing mode, smoothly fix the door and press “Start”.

Also check out: Is it possible connect the dishwasher to hot water?

Conclusion

If the test run was evaluated as “good”, and the machine did not reveal any shortcomings, then the test run can be considered completed. The dishwasher should cool, the detergent must be added, but the salt and rinse aid will last for a long time.

Everything, your new assistant is ready for further work.