Error e09 (Fig. 1) on the display of the dishwasher of the German brand Bosch signals a serious electrical problem. Repair should be started immediately, but first, you need to understand what the problem is.
Why does error e09 appear?
In 10% of cases, the error e09 in the dishwasher can report:
- software failure;
- about a fault in the wiring, poor contact in the outlet;
- about the inconsistency of the cross section of the electric cable of the power consumption of the equipment;
- About the deteriorated temperature sensor;
- about errors in the operation of the main module.
In 90% of cases, this is a breakdown of the heating element, as a result of which it is necessary to repair or replace this heater.
The following provoking factors lead to the failure of the heater:
- period of operation of the machine: the older it is, the more probability of malfunction;
- scale on the heater, as a result of which it heats the water longer, constantly overheats and, in the end, burns out;
- filter clogging: as a result, poor water circulation and overheating of the heating element, as a result, it fails;
- worn out pipes, hoses, gaskets lead to depressurization and water contact - short circuit, heater burns out.
Fault code e27 - How to fix it, you can find out the link.
How to troubleshoot in ten percent of cases
If the error is highlighted for the first time, perhaps not everything is so bad and it is enough to reload the program. To do this, turn off the car by unplugging the plug from the outlet, wait 10 minutes and turn it on. If the error no longer appears, then the problem is resolved.
Check wiring, replace the outlet, eliminate the defect in the mains immediately. Procrastination can lead to fire, electric shock, serious damage to equipment with expensive repairs.
If it is revealed that the water does not stop heating, or in general the dishwasher does not heat water, pay attention to the temperature sensor. Overheating of the heater will lead to its failure and may even cause a fire. Therefore, the dishwasher must be de-energized immediately. Need to repair or replace the temperature sensor.
Malfunctions of the elements of the control unit can lead to incorrect operation of the temperature control circuit of the water heater. Damage to the sensor occurs due to power surges. This malfunction is eliminated by replacing the electronic components on the control unit.
What to do if the heating element fails?
The first option is to invite a specialist service center to replace a wrecked unit. The second option is to try to cope on your own, not forgetting the safety rules.
Important detail! Error e09 of the bosch dishwasher is diagnosed only in third-generation models. Structurally, the heater is part of the circulation pump (Fig. 2), therefore, the entire assembly is subject to replacement. When buying parts, you should consider the model of the machine so as not to make a mistake in choosing.
First you need to get to the burned site. This is the most time-consuming process, because the machine will have to be disassembled almost completely.
The procedure is as follows:
- Disconnect equipment, disconnect all communications.
- Free the machine chamber from dishes, nets, wire racks.
- Release latches on the housing, remove the housing.
- A metal plate is fixed under the door of the dishwasher.It must be removed by unscrewing the bolts.
- Carefully remove thermal insulation, set aside.
- Now the turn of the pallet is to unscrew the bolts (Fig. 3).
- Remove the lower diffuser, filter, mesh at the bottom of the camera (Fig. 4).
- Unclip the circulation pump.
- For further work, the position of the washing machine should be changed by placing it on the back wall (Fig. 5).
- Disconnect the nozzle from the pump and slowly, without jerking, pull out the sump.
- The drain pump is removed by turning clockwise.
- Fastenings of the circulation block hooks. Carefully remove the part from the mounts, having previously disconnected the wires, hoses, pipes.
- Remove the clamp and wires connecting the heater to the pump. The wiring diagram must first be fixed in order to assemble everything correctly later.
- Install a new node.
- Assemble parts in reverse order.
- Check the performance of the equipment.
Find out in our article how to fix error e24 in the dishwasher.
Some tips for future operation.
In order not to encounter the error e09 in the future, when using the dishwasher, you should follow some simple rules:
- periodically check the condition of gaskets, gaskets, hoses and pipes, timely replace worn out to avoid leaks;
- regularly clean and rinse the filter mesh from debris, mucus and food debris, to prevent blockage and fluid congestion;
- use means to soften water, prevent the appearance of scale;
- in case of frequent power surges, install a stabilizer to prevent failure of the control module;
- use the services of a qualified specialist to properly connect the installed dishwasher to a household electrical outlet.
These tips will help extend the life of your home caregiver and minimize the risk of breakdowns, followed by expensive dishwasher repairs.